Showing posts with label Tilt Hood. Show all posts
Showing posts with label Tilt Hood. Show all posts

Saturday, July 10, 2010

FLOPPER STOPPER

The rearmost bottom corners of a Sonett III hood assembly is normally held in place with a bolt. The tilt hood on the Electric Norseman makes that sort of fix just a tad unhandy. My fix is a set of inclined pins--one on each side of the car--welded to the square steel inner hood reinforcement. Each pin--as the hood is lowered and latched at the back, slips over a horizontal pin bolted to the frame. When the hood is latched down, the lower corners of the hood just snug up to the frame of the car, so it all lines up and doesn't flop around.

I got in a bitch of a position to take this under-fender photo, but you can clearly see the inclined pin. As the hood goes DOWN, the pin draws the hood IN, against the frame of the car. I made the bracket--that is bolted to the frame--adjustable, so it is entirely possible to get it "just right".


Two drawings in one....the main drawing shows the tilt hood partly open. No. 2 [in both drawings] is the square steel reinforcement frame inside the 'glass hood skin. You can see where the inclined pin is welded to that frame, and how, when the hood is closed, the pin slides right over the second pin on the strap bolted to the frame of the car.

In the smaller drawing on the right, No. 1 is the fiberglass skin of the car, No. 2 is the square steel reinforcing frame, and No. 3 shows how the fiberglass hood skin is sucked right in against the frame of the car. Thus "gestopping der flopping." Simple fixes are almost always the best.

Friday, July 2, 2010

HAVING A RE-LATCH

This is the OTHER half of the hood latch system for the tilt hood mechanism in the Electric Norseman '73 Sonett. This is the SECOND pin...I built the FIRST pin half an inch too bloody short! The fair Kathleen said something about "...dumb shit...", tho' I didn't hear all of that....

The latch PIN threads into a nut welded to a sleeve, that is in turn welded to a mount plate. The mount plate bolts to the square steel frame for the tilt hood mechanism. The pin is adjustable in all three planes. The view is the passenger side of the hood [with the hood open]. The stock hood door is on the left side of the photo.

The hood pin [top center] just about ready to drop into the latch assembly. The hood ass'y is just about closed. Uhhh...I THINK it is going to reach, now....Photo taken from inside the right fender well.

The pin is in place, locked into the latch assembly. YES! It DID reach! Note that the Fiat latches have a strong "push-up" spring [out of view in this photo] that pushes the hood ass'y up about 1.5 inches when the latch is released. So now the Norseman has a new latch on life.....

Friday, June 11, 2010

TILT HOOD TALK

I got a call from a Sonett owner who wanted more detailed dimensions of the hood latch arrangement that I showed in the blog. Truth is, Sonetts are almost KIT CARS and no two Sonetts measure the same in any one dimension. Also, I built this to fit the steel reinforcement "skeleton" that I built and bolted to the underside of the hood ass'y. My next act is to fabricate the lock-down drop link that will bolt to the skeleton. The drop down link fits into the latches and locks the hood down on both sides. Ah...THAT should be interesting!

This is the FOURTH generation of tilt hoods I have done on Sonett III cars. I will add all of this information, with dimensioned drawings, in my book SAAB SONETT III TILT HOOD CONVERSION, available from Ashcraft's Vintage Saab Parts.

Converting a Sonett III hood ass'y to tilt is a MAJOR job, no doubt about it. But to those who have made the conversion, actually being able to easily DO something in the engine bay makes it all very worthwhile. And at a gathering of the Troll Faithful, the tilt-hood Sonett III is the one that will have all the lookers. Guaranteed.

Thursday, June 10, 2010

LATCH 'ER DOWN...SONETT HOOD LATCH

A tilt hood requires a fairly interesting latch-down arrangement. I have used several different types, and I think this one, using Fiat latch assemblies, is the best because it's simple. Since you probably don't have any Fiat latches laying around, you can check your local wrecking yard for cars with similar style latches.

You are looking at the RIGHT side of a Sonett III engine bay frame, just behind the coil spring. The 0.125" thick plate bolts to the frame and supports [A] the cross rod [top center], and [B] the Fiat hood latch assembly.


I welded a pair of 5/16" bolts to mount the Fiat hood latch ass'y.


Fiat hood latch set into place on the bolts. I attached the release link [at the bottom of photo] to the actuating arm on the cross rod. Just out of sight at the bottom is an adjustable Heim ball socket end. Most any real auto parts store carries ball socket ends.


This shows the 0.375" diameter cross bar and actuating arm ass'y, in place and attached to the release link on the Fiat latch. I had to weld 2 pieces of rod together to get a cross bar long enough!


Another view of the cross bar, the actuating arm and the release link, attached to the Fiat latch assembly. The angle steel on the right is part of our Drakenparts front frame stiffener kit.


This is the Fiat latch that I mounted on the LEFT side of the engine bay [coil spring is on the left, just out of sight]. The mocked-up clevis and rod shows where the hood release pull rod will go through the front wheel splash panel, into the cabin. The pull link directly below the latch also has an adjustable Heim ball socket end.
I like this installation because it lets me locate the release pull rod in the same mount where the original hood release "T" handle was mounted. Simple and "sanitary"!

Tuesday, June 8, 2010

Sonett Headlamp Magic

Access is the name of the game with the Electric Norseman. But then there are those pesky pop up headlamps that mount to the hood assembly itself. Hmmmm...I have handled them in a number of ways on S-III tilt hoods but I like this one the best---the headlight assembly is mounted to the frame of the car, NOT the fiberglass hood.

The headlamp up/down mechanism remains in place and in alignment, whether the hood ass'y is open or closed.


This is the pop-ups on the bench, with the actuating cross bar in position. Some of the mounting brackets are also shown.


The right side pop-up bucket, mounted to the frame. I built the mounts so the buckets are adjustable in all three planes. Making them go up and down is GOOD! Making them fit the hood openings at the same time is even BETTER!


Left side bucket ass'y mounted to the frame. How does it work? Like a champ! See--the headlamp buckets don't know they aren't still mounted to the hood!

Monday, June 7, 2010

ELECTRIC NORSEMAN

Yup. It IS an electrified 1973 Sonett. I call it "The Electric Norseman." The 110 volt charging port is where the gas cap ustawuz. I have the battery racks installed for eight big ol' 12 volt electric car buggers. Six in the trunk area and two up front, plus a small "regular" battery to run the wipers, the fans, the lights, and oh, yeah, the air horns.


So everybody asks. "How fast?" and "How far?" I'm hoping for 50mph with a 50 mile range. We'll know that when it's finished. I'm keeping it as LIGHT and SLIPPERY as possible. More on those efforts later---stay tuned.


I've been a Saab "wrench" too long. Can't stand a Sonett without a tilt hood. Note that the regular hood door still works AND that the pop-up headlights remain in place [and alignment] when the hood is tilted forward.
I'm working on the custom hood latching system in my shop this week, so I'll have photos and info soon!